Viscous Flow Assignment 3 — Couette Flow
 Question #1
Use the momentum equations in viscous form and the mass conservation equation to determine the velocity distribution and the mass flow rate per unit depth between two planes located at $y=0$ and $y=H$ for $x\gg H$:
The two planes are rigid and the problem is at steady-state.
 06.27.16
 Question #2
Two equally big circular plates rotate very close to each other in a viscous fluid as follows:
One of the plates is driven by a constant power ${\cal P}_{\rm L}$ and at a constant angular speed $\omega_{\rm L}$. The other plate is braked with a power ${\cal P}_{\rm R}$. For a plate radius $R$ much larger than the distance between the plates $H$, do the following:
 (a) Determine the angular speed $\omega_{\rm R}$ as a function of $\omega_{\rm L}$ and if the breaking power ${\cal P}_{\rm R}=\frac{1}{2}{\cal P}_{\rm L}$ (b) If $\omega_{\rm R}=0$, $\mu=10^{-2}$ kg/ms, $\rho=800$ kg/m$^3$, $R=0.1$ m, and $H=3$ mm, determine the amount of power ${\cal P}_{\rm L}$ needed to sustain $\omega_{\rm L}=3000~$rpm.
 Question #3
A crankshaft journal bearing in an automobile engine is lubricated by oil with a kinematic viscosity of $10^{-4}$ m$^2$/s and a density of 885 kg/m$^3$:
The bearing inner diameter $D_{\rm i}$ is of 10 cm, the bearing outer diameter $D_{\rm o}$ is of 11 cm, and the bearing rotates at $7200$ rpm. The bearing is under no load so the clearance is symmetric. Determine the torque per unit depth and the power dissipated per unit depth.
 Question #4
A piston with a diameter of $D_{\rm i}=100$ mm and a length $L=150$ mm is moving concentrically in a cylinder with a diameter $D_{\rm o}=100.1$ mm. The gap between the cylinder and the piston is filled with oil:
The kinematic viscosity of the oil is 65 cSt and the density is 885 kg/m$^3$. How big is the force that has to be applied to move the piston in the axial direction with a speed $q=3$ m/s if only the viscous resistance is considered? Note: 1 cSt=$10^{-6}$ m$^2$/s.
 Question #5
Consider the following piston-cylinder assembly:
In the latter, the cylinder is fixed while the piston is allowed to move and is subject to a gravity force $mg$. Knowing that the gravitational acceleration is of $g=9.8$ m/s$^2$, that the radius of the piston and of the cylinder are of $R_{\rm p}=10$ cm and $R_{\rm c}=10.3$ cm, respectively, that the height of the piston is of $H=5$ cm, that the density of the piston is of $\rho_{\rm p}=2000$ kg/m$^3$, and that the oil viscosity and density are of $\mu_{\rm oil}=0.5$ kg/ms and $\rho_{\rm oil}=800$ kg/m$^3$, do the following:
 (a) Find the force acting on the piston in the positive $y$ direction due to viscous effects as a function of the piston speed $q$. For simplicity, you can assume that $R_{\rm c}-R_{\rm p}\ll R_{\rm c}$. (b) Using the expression derived in (a), find the maximum speed $q$ that the piston would get if it is allowed to fall freely assuming negligible drag on its top and bottom surfaces.
 10.12.17
 2. $\omega_{\rm L}/2$, 51.7 W. 3. 10.48 N, 7903 W/m. 4. 5. 6.02 m/s.
 $\pi$